Diodes AP6502 Manual de usuario Pagina 8
- Pagina / 15
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
AP6502
Document Number: DS35423 Rev. 9 - 2
8 of 15
www.diodes.com
January 2013
© Diodes Incorporated
NEW PRODUCT
A
P6502
Applications Information
Theory of Operation
The AP6502 is a 2A current mode control, synchronous buck regulator with built in power MOSFETs. Current mode control assures excellent
line and load regulation and a wide loop bandwidth for fast response to load transients. Figure 3 depicts the functional block diagram of
AP6502.
The operation of one switching cycle can be explained as follows. At the beginning of each cycle, HS (high-side) MOSFET is off. The error
amplifier (EA) output voltage is higher than the current sense amplifier output, and the current comparator’s output is low. The rising edge of
the 340kHz oscillator clock signal sets the RS Flip-Flop. Its output turns on HS MOSFET. The current sense amplifier is reset for every
switching cycle.
When the HS MOSFET is on, inductor current starts to increase. The current sense amplifier senses and amplifies the inductor current. Since
the current mode control is subject to sub-harmonic oscillations that peak at half the switching frequency, ramp slope compensation is utilized.
This will help to stabilize the power supply. This ramp compensation is summed to the current sense amplifier output and compared to the
error amplifier output by the PWM comparator. When the sum of the current sense amplifier output and the slope compensation signal
exceeds the EA output voltage, the RS Flip-Flop is reset and HS MOSFET is turned off.
For one whole cycle, if the sum of the current sense amplifier output and the slope compensation signal does not exceed the EA output, then
the falling edge of the oscillator clock resets the Flip-Flop. The output of the error amplifier increases when feedback voltage (VFB) is lower
than the reference voltage of 0.925V. This also increases the inductor current as it is proportional to the EA voltage.
If in one cycle the current in the power MOSFET does not reach the COMP set current value, the power MOSFET will be forced to turn off.
When the HS MOSFET turns off, the synchronous LS MOSFET turns on until the next clock cycle begins. There is a “dead time” between the
HS turn off and LS turn on that prevents the switches from “shooting through” from the input supply to ground.
The voltage loop is compensated through an internal transconductance amplifier and can be adjusted through the external compensation
components.
Enable
Above the ‘EN Rising Threshold’, the internal regulator is turned on and the quiescent current can be measured above this threshold. The
enable (EN) input allows the user to control turning on or off the regulator. To enable the AP6502, EN must be pulled above the ‘EN Lockout
Threshold Voltage’ and to disable the AP6502, EN must be pulled below ‘EN Lockout Threshold Voltage - EN Lockout Hysteresis’
(2.2V-0.22V =1.98V).
External Soft Start
Soft start is traditionally implemented to prevent the excess inrush current. This in turn prevents the converter output voltage from
overshooting when it reaches regulation. The AP6502 has an internal current source with a soft start capacitor to ramp the reference voltage
from 0V to 0.925V. The soft start current is 6uA. The soft start sequence is reset when there is a Thermal Shutdown, Under Voltage Lockout
(UVLO) or when the part is disabled using the EN pin.
External Soft Start can be calculated from the formula below:
DT
DV
*C
SS
I =
Where;
I
SS
= Soft Start Current
C = External Capacitor
DV = change in feedback voltage from 0V to maximum voltage
DT = Soft Start Time
Current Limit Protection
In order to reduce the total power dissipation and to protect the application, AP6502 has cycle-by-cycle current limiting implementation. The
voltage drop across the internal high-side MOSFET is sensed and compared with the internally set current limit threshold. This voltage drop is
sensed at about 30ns after the HS turns on. When the peak inductor current exceeds the set current limit threshold, current limit protection is
activated. During this time the feedback voltage (VFB) drops down. When the voltage at the FB pin reaches 0.3V, the internal oscillator shifts
the frequency from the normal operating frequency of 340kHz to a fold-back frequency of 102kHz. The current limit is reduced to 70% of
nominal current limit when the part is operating at 102kHz. This low fold-back frequency prevents runaway current.
- AP6502 1
- (Note 7) (@T 3
- © Diodes Incorporated 5
- V = 12V 6
- L = 10µH 6
- Theory of Operation 8
- External Soft Start 8
- Current Limit Protection 8
- Under Voltage Lockout (UVLO) 9
- Over Voltage Protection 9
- Thermal Shutdown 9
- Setting the Output Voltage 9
- Compensation Components 9
- Inductor 10
- Inductor (cont.) 11
- Input Capacitor 11
- Output Capacitor 11
- PC Board Layout 12
- External Bootstrap Diode 12
- (1) SO-8EP 13
- (2) SO-8 14
- NEW PRODUCT 15
Relacionado con productos y manuales para Hardware Diodes AP6502
Hardware Diodes AP6015 Manual de usuario
(18 paginas)
(18 paginas)
Hardware Diodes AP5101 Manual de usuario
(15 paginas)
(15 paginas)
Hardware Diodes AP6503 Manual de usuario
(15 paginas)
(15 paginas)
Hardware Diodes AP6503A Manual de usuario
(15 paginas)
(15 paginas)
Hardware Diodes AP6502A Manual de usuario
(14 paginas)
(14 paginas)
Hardware Diodes AP6507 Manual de usuario
(13 paginas)
(13 paginas)
Hardware Diodes AP65400 Manual de usuario
(15 paginas)
(15 paginas)
Hardware Diodes AP65200 Manual de usuario
(18 paginas)
(18 paginas)
Hardware Diodes AP65402 Manual de usuario
(15 paginas)
(15 paginas)
Hardware Diodes AP6508 Manual de usuario
(14 paginas)
(14 paginas)
Hardware Diodes AP65403 Manual de usuario
(15 paginas)
(15 paginas)
Hardware Diodes AP65500 Manual de usuario
(15 paginas)
(15 paginas)
Hardware Diodes AP65502 Manual de usuario
(15 paginas)
(15 paginas)
Hardware Diodes AP65503 Manual de usuario
(15 paginas)
(15 paginas)
Hardware Diodes AT5503 Manual de usuario
(12 paginas)
(12 paginas)
Hardware Diodes AP65550 Manual de usuario
(14 paginas)
(14 paginas)
Hardware Diodes AUR9705 Manual de usuario
(16 paginas)
(16 paginas)
Hardware Diodes AUR9710 Manual de usuario
(13 paginas)
(13 paginas)
Hardware Diodes AUR9707 Manual de usuario
(15 paginas)
(15 paginas)
Hardware Diodes AUR9703 Manual de usuario
(20 paginas)
(20 paginas)
One For All URC-6210 manuály
Uživatelské manuály a uživatelské příručky pro Dálkové ovládání One For All URC-6210.
Poskytujeme 1 manuály pdf One For All URC-6210 ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Comentarios a estos manuales